Decorative wall mouldings: how to create panels that work

    Mouldings & walls · 6 min read

    Wall with rectangular moulding panels in a soft colour, with a white skirting board and a light floor

    Decorative wall mouldings turn a flat wall into a wall with depth, rhythm and character. They usually take the form of rectangular panels made from slim mouldings, sometimes combined with a horizontal dado rail. Whether the result looks classic or modern depends on the profile, the colour and above all the layout. Panels that are neatly spaced across the wall, with crisp mitres and invisible joints, make the difference between "a few strips on the wall" and mouldings that look as if they belong to the house.

    Why decorative mouldings on the wall?

    A decorative moulding adds relief. Light falling along the profile creates small shadows, which makes the wall livelier without anything having to hang on it. They are often chosen for:

    • living rooms and dining rooms, as a calm backdrop for furniture;
    • bedrooms, behind the bed as an alternative to a headboard;
    • hallways and stairwells, where a long wall gains structure;
    • characterful homes, to bring back mouldings that were once there.

    Mouldings are also widely used in hotels and commercial spaces. In a hotel in Maastricht, TipTop Plinten handled all the wall panels, decorative mouldings and caulking in RAL 9010.

    How do you lay out the panels?

    The layout is the most important part of the job. A few principles:

    Start with the fixed lines

    Skirting board, ceiling, windows, doors and switches determine where there is space. Panels that line up neatly with the top of a door or the bottom of a window look logical. Panels that fall just beside them look accidental.

    Equal spacing

    Ideally, keep the space between the panels and between panel and wall edge equal. A common approach is the same measurement at the sides as between the panels, with a slightly larger measurement at the top and bottom.

    High and low

    On a tall wall you can work with two rows: a low row of panels below a dado rail and a taller row above it. With a standard ceiling height, a single row of tall panels often looks calmer. In wall mouldings and wainscoting you can read more about the height of wainscoting.

    Draw it out

    Draw the layout to scale or mark it on the wall with tape. That way you can see before any cutting whether the proportions work with the room and the furniture.

    Which profile should you choose?

    • Slim and flat: modern and calm, suits clean-lined interiors.
    • Medium width with a curve or step: timeless, suits most homes.
    • Wide and richly profiled: classic, especially suited to high ceilings and townhouses.

    As a rule of thumb: the higher the room, the heavier the profile can be. A heavy profile in a low room soon looks busy. You will find ideas for modern applications in decorative mouldings in a modern interior.

    Which material?

    Decorative mouldings are made from MDF, solid wood, plaster and various plastics, among others. For painted wall panels, MDF is a popular base: it is dimensionally stable, smooth and takes paint evenly. Solid wood suits classic interiors or situations where the wood stays visible. TipTop Plinten works with MDF and solid wood, and deliberately does not fit plastic mouldings.

    Close-up of a mitre in the corner of a wall moulding panel, neatly caulked and painted

    How are decorative mouldings fitted on the wall?

    1. Checking the surface

    The wall must be dry, clean and sound. Loose layers of paint or soft plaster give adhesive no grip. Major irregularities are repaired beforehand.

    2. Setting out

    The panels are set out on the wall with a laser or spirit level. With an uneven floor or ceiling, we look at which line catches the eye most, so the panels look straight.

    3. Mitre cutting

    The corners of a panel are cut as a mitre joint, usually at 45 degrees. The more accurate the mitre, the less filler is needed and the crisper the corner stays.

    4. Fixing

    Decorative mouldings are generally bonded with construction adhesive, with thin pins where needed to hold the moulding in place while it cures.

    5. Finishing

    Pin holes and mitres are filled. The joint between moulding and wall is sealed with acrylic caulk, which can be painted over. Then the moulding and wall are painted. Silicone sealant is not suitable here, because paint does not adhere to it.

    Colour: tone-on-tone or contrast?

    • Tone-on-tone: mouldings and wall in the same colour. The profile provides depth, while the whole stays calm. A popular choice in modern interiors.
    • Contrast: for example white mouldings on a dark or coloured wall. The panels become a clear graphic element.
    • Sheen level: a slightly higher sheen on the mouldings than on the wall makes the profile subtly stand out and is easier to wipe clean.

    Common mistakes with decorative wall mouldings

    A few things often go wrong, both with DIY and with rushed work:

    • Panels that do not line up. A panel that falls just beside the line of a door or window draws more attention than the panel itself. Line up with what is already there.
    • Too many small panels. Lots of narrow sections make a wall look busy. Fewer, larger panels often look more grown-up.
    • A profile that is too heavy. In a room with a standard ceiling height, a wide, richly detailed profile soon looks busy.
    • Open mitres. A gap in the corner of a panel is visible from a distance. It is usually caused by an inaccurate cutting angle or a corner that is not exactly square.
    • The wrong sealant. Silicone sealant along a moulding that needs painting will stop the paint from adhering. Use paintable acrylic caulk.
    • Forgetting the sockets. A panel that runs across a socket or switch has to be interrupted. Keep them outside the mouldings in the layout, or have them moved beforehand by a qualified electrician.

    Combining decorative mouldings on the wall and ceiling

    Wall panels are often combined with coving, so that the transition between wall and ceiling is also neatly finished. Read more in decorative ceiling mouldings. If you prefer a bigger intervention, living room wall panels are an alternative.

    Having decorative wall mouldings fitted?

    TipTop Plinten, based in 's-Hertogenbosch, fits decorative mouldings, wall mouldings and coving throughout the Netherlands, for homeowners, contractors, interior fit-out companies and hotels. Read more on the decorative mouldings and coving page.

    Send a photo of the wall, the dimensions and, if you have one, an example of the style you are looking for via the contact page. The quote is free and without obligation, and we can communicate in English, Dutch, German, Turkish, Persian or Arabic. An on-site measurement is optionally available for €75 incl. VAT; this amount is credited as a discount on jobs above a minimum project size.

    Frequently asked questions

    Start with the fixed points: skirting board, ceiling, windows, doors and any dado rail. Then divide the wall into panels with equal spacing, so the margins are the same on both sides. Draw the layout to scale or mark it out on the wall beforehand.

    Decorative mouldings are available in MDF, solid wood, plaster and various plastics, among others. MDF is a popular choice for painted wall panels because it is dimensionally stable and takes paint evenly. TipTop Plinten works with MDF and solid wood, not with plastic.

    Not necessarily, but in the same colour they often look calm and modern; the profile then provides the play of shadow. A contrasting colour, for example white mouldings on a coloured wall, puts more emphasis on the panels.

    Usually with construction adhesive, sometimes supplemented with thin pins while the adhesive cures. Then joints and holes are filled and the junction with the wall is sealed with paintable acrylic caulk, after which everything is painted.

    Yes, but the layout then has to look right visually, not just by the spirit level. With a sloping ceiling or uneven floor, we look at which line stands out most and adjust the layout to it.

    Related articles

    Related

    Skirting board installation? Request a free quote

    On-site measurement €75 incl. VAT (credited for orders above a minimum project size)